Sketcher CreatePolyline/ru: Difference between revisions

From FreeCAD Documentation
(Created page with "Этот инструмент работает как инструмент Sketcher Линия, но создает непрерывные отрезк...")
No edit summary
Line 13: Line 13:
==Описание==
==Описание==


Этот инструмент работает как инструмент [[Sketcher CreateLine|Sketcher Линия]], но создает непрерывные отрезки линии и дуги, соединенные их вершинами. При запуске инструмента указатель мыши меняется на белый крест с красным значком ломаной линии. Координаты указателя отображаются рядом с ним синим цветом в режиме реального времени.
Этот инструмент работает как инструмент [[Sketcher CreateLine| Линия]], но создает непрерывные отрезки линии и дуги, соединенные их вершинами. При запуске инструмента указатель мыши меняется на белый крест с красным значком ломаной линии. Координаты указателя отображаются рядом с ним синим цветом в режиме реального времени.


[[Image:Sketcher_PolylineExample1.png|none]]
[[Image:Sketcher_PolylineExample1.png|none]]

Revision as of 03:51, 30 August 2019

Sketcher Полилиния

Системное название
Sketcher Полилиния
Расположение в меню
Эскиз → Геометрия эскиза → Создать полилинию
Верстаки
Sketcher
Быстрые клавиши
Нет
Представлено в версии
-
См. также
Sketcher Line

Описание

Этот инструмент работает как инструмент Линия, но создает непрерывные отрезки линии и дуги, соединенные их вершинами. При запуске инструмента указатель мыши меняется на белый крест с красным значком ломаной линии. Координаты указателя отображаются рядом с ним синим цветом в режиме реального времени.

Polyline started with a line, a tangent arc, a perpendicular arc then a tangent line

How to use

The polyline always starts with a straight line segment: click - move the mouse - click. Move the mouse again. After placing the first line segment, the Sketcher polyline tool has multiple modes that can be toggled with the M key. For example you can draw tangent or perpendicular arcs following a line or arc segment. Repeatedly pressing the M key toggles through these different modes:

  1. Press the M key: the new segment is a line which is perpendicular to the previous segment.
  2. Press the M key again: the new segment is a line which is tangential to the previous segment.
  3. Press the M key again: the new segment is an arc which is tangential to the previous segment.
  4. Press the M key again: the new segment is an arc which is perpendicular (left) to the previous segment.
  5. Press the M key again: the new segment is an arc which is perpendicular(right) to the previous segment.
  6. Press the M key again: You are again in the state where you started; the line is only connected with a coincidence to the previous segment.
  • v0.18 and above While in any of the arc modes, holding down the Ctrl key (MacOS: CMD key) and moving the cursor causes the arc to snap by increments of 45 degrees, relative to the previously created polyline segment.
  • Pick points on an empty area of the 3D view, or on an existing object (auto constraints must be active in TaskView).
  • Pressing Esc or clicking the right mouse button before closing the polyline to a loop ends the current polyline and you can continue with a new one. Pressing Esc or clicking the right mouse button again ends the polyline function.
  • Pressing Esc or clicking the right mouse button after closing the polyline to a loop ends the polyline function.