Part: PartDesign Pad(protuberanță)

From FreeCAD Documentation
Revision as of 00:56, 6 February 2020 by FuzzyBot (talk | contribs) (Updating to match new version of source page)

PartDesign Pad

poziția meniului
Part Design → Pad
Ateliere
PartDesign
scurtătură
nici unul
Prezentat în versiune
-
A se vedea, de asemenea,
nici unul

Descriere

Instrumentul Pad extrude o schiță într-un solid în direcția normală la planul schiței. Începând cu versiunea v0.17, fațete pe solid pot de de asemenea utilizate.

Sketch (A) shown on the left; end result after pad operation (B) on the right.

version 0.16 and below If the selected sketch is mapped to the face of an existing solid or another Part Design feature, the pad will be fused to it.

Cum se utilizează

  1. Select the sketch to be padded. In v0.17 and above, a face on the existing solid can alternatively be used.
  2. Press the Pad button.
  3. Set the Pad parameters (see next section).
  4. Click OK.

Opțiuni

Când se creează o protuberanță(Pad), vizualizarea Combo se comută automat în panoul Activități, afișând dialogul Parametri pad .

Type

Tipul oferă cinci modalități diferite de a specifica lungimea la care va fi extrudat tamponul.

Dimension

Enter a numeric value for the length of the pad. The default direction for extrusion is away (outside of) the support, but it can be changed by ticking the Reversed option. Extrusions occur normal to the defining sketch plane. With the option Symmetric to plane the pad will extend half of the given length to either side of the sketch plane. Negative dimensions are not possible. Use the Reversed option instead.

Two dimensions

This allows to enter a second length in which the pad should extend in the opposite direction (into the support). Again can be changed by ticking the Reversed option.

To last

The pad will extrude up to the last face of the support in the extrusion direction. If there is no support, an error message will appear.

To first

The pad will extrude up to the first face of the support in the extrusion direction. If there is no support, an error message will appear.

Up to face

The pad will extrude up to a face in the support that can be chosen by clicking on it. If there is no support, no selections will be accepted.

Length

Definește lungimea protuberanței. Unitățile multiple pot fi utilizate independent de preferințele unităților utilizatorului(m, cm, mm, nm, ft or ', in or ").

Symmetric to plane

Bifați caseta de selectare pentru a extinde jumătate din lungimea dată la fiecare parte a planului de schiță.

Reversed

Reverses the direction of the pad.

Proprietăți

  • DATERefine: version 0.17 and above true or false. Cleans up residual edges left after the operation. This property is initially set according to the user's settings (found in Preferences → Part design → General → Model settings). It can be manually changed afterwards. This property will be saved with the FreeCAD document.

Limitări

  • Like all Part Design features, Pad creates a solid, thus the sketch must include a closed profile or it will fail with a Failed to validate broken face error. There can be multiple enclosed profiles inside a larger one, provided none intersect each other (for example, a rectangle with two circles inside it).
  • The algorithm used for To First and To Last is:
    • Create a line through the centre of gravity of the sketch
    • Find all faces of the support cut by this line
    • Choose the face where the intersection point is nearest/furthest from the sketch
This means that the face that is found might not always be what you expected. If you run into this problem, use the Up to face type instead, and pick the face you want.
For the very special case of extrusion to a concave surface, where the sketch is larger than this surface, extrusion will fail. This is a unresolved bug.